Preparation method of carbon steel pipe

Release time:

2022-09-16

The raw material of carbon steel pipe is round tube blank, which needs to be cut and processed by a cutting machine to form a billet with a length of about 1 meter, and then sent to the furnace for heating through a conveyor belt. The billet is fed into the furnace for heating, with a temperature of approximately 1200 degrees Celsius.

The raw material of carbon steel pipe is round tube blank, which needs to be cut and processed by a cutting machine to form a billet with a length of about 1 meter, and then sent to the furnace for heating through a conveyor belt. The billet is fed into the furnace for heating, with a temperature of approximately 1200 degrees Celsius. The fuel is hydrogen or acetylene. Temperature control in the furnace is a crucial issue. After the round tube billet is discharged from the furnace, it needs to be pierced through by a pressure piercing machine. The commonly used piercing machine is a conical roller piercing machine, which has high production efficiency, good product quality, large perforation and expansion capacity, and can pierce various steel grades. After perforation, the round tube blank is sequentially rolled, continuously rolled, or extruded by three rollers. After squeezing, the pipe needs to be detached and sized. The sizing machine uses a conical drill bit to rotate at high speed into the steel billet for drilling, forming a steel pipe. The inner diameter of the steel pipe is determined by the outer diameter length of the sizing machine drill bit. After the steel pipe is sized, it enters the cooling tower and is cooled by water spray. After cooling, the steel pipe needs to be straightened. After straightening, the steel pipe is transported by a conveyor belt to a metal inspection machine (or hydraulic test) for internal inspection. If there are cracks, bubbles, and other issues inside the steel pipe, they will be detected. After the quality inspection of steel pipes, strict manual selection is also required. After the quality inspection of the steel pipe, the number, specification, production batch number, etc. are sprayed with paint. And lifted into the warehouse by a crane.

LATEST NEWS

What is the material of carbon steel plate and what are its advantages and disadvantages

It is a type of steel with a carbon content lower than 2.11% and without intentionally adding metallic elements, and can also be called plain carbon steel or carbon steel. In addition to carbon, it also contains a small amount of elements such as silicon, manganese, sulfur, and phosphorus inside. The higher the carbon content, the better the hardness and strength, but the lower the plasticity.

2022-09-16

What is the difference between carbon steel and stainless steel

The density of carbon steel is slightly higher than that of ferritic and martensitic stainless steel, but it is lower for austenitic stainless steel, so the difference between carbon steel and stainless steel is different.

2022-09-16

Four processes of steel bar processing

The processing of steel bars generally involves four processes: rust removal of steel bars; Straightening of steel bars; Steel bar cutting; Forming of steel bars. When the steel bar joint is connected with straight or conical threads, it is also necessary to add the steel bar end upsetting and thread processing procedures. Rebar batching and replacement Rebar replacement

2022-09-16

Characteristics of copper pipes

Lightweight, with good thermal conductivity and high low-temperature strength. Commonly used in the manufacturing of heat exchange equipment (such as condensers). It is also used for assembling low-temperature pipelines in oxygen production equipment. Copper pipes with small diameters are commonly used for conveying pressurized liquids (such as lubrication systems, oil pressure systems, etc.) and as pressure measuring pipes for instruments.

2023-03-24

Advantages of I-beams

I-shaped beams are hollow web members. For high-strength materials, hollow web members are better than solid web members in terms of weight, material, and labor saving. This cross-sectional design mainly uses the flange farthest from the centroid to resist bending moments (because the farther the flange is, the greater the moment of inertia), and mainly uses the web to resist shear. As for the inconvenience in making it, it can be solved by factory or molding. Saving materials, labor, and time is efficiency.

2023-03-14

How are stainless steel pipes classified?

Stainless steel pipes are divided into ordinary carbon steel pipes, high-quality carbon structural steel pipes, alloy structural pipes, alloy steel pipes, bearing steel pipes, stainless steel pipes, as well as bimetallic composite pipes, coated and coated pipes to save precious metals and meet special requirements. There are various types and uses of stainless steel pipes, with varying technical requirements and production methods. The current production of steel pipes has an outer diameter range of 0.1-450mm and a wall thickness range of 0.01-250mm. To distinguish its characteristics, steel pipes are usually classified according to the following method.

2023-03-06

Feedback

*
*
Submit